UNLESS STATED THESE ARE GOOD USED TAKE OFF PARTS.
UPS CHARGES ARE ADDITIONAL AND VARY BY DESTINATION AND
PACKAGED WEIGHT OF PART/PARTS.
| PART DESCRIPTION |
PRICE |
ANY NOTES |
| Clutch - NEW |
58.00 |
exchange or core charge added |
| Pressure plate - NEW |
79.00 |
exchange or core charge added |
| Throw out bearing NEW |
58.00 |
aftermarke troller bearing type |
| |
|
|
| Clutch release yoke |
10.00 |
advise straight or bent&includes pin |
| Clutch operating rod |
5.00 |
with clevis ends |
| Clutch pedal |
20.00 |
with sleeve or with out |
| Clutch pedal return spring |
4.00 |
or set of 3 for 10.00 |
| Clutch housing |
50.00 |
(center section) |
| Hand hole cover |
20.00 |
with bar and nut (round) |
| Clutch housing cover |
15.00 |
(half moon) |
| |
|
|
| Transmission
case/housing |
75.00 |
cleaned, visually checked for cracks |
| Ring gear & pinion shaft asm |
75.00 |
-called differential case in book- |
| Rear trans cover plate |
40.00 |
|
| Bearing retainer |
15.00 |
|
| Bearing retainer shims |
3.00 |
set of 4 |
| Transmission clutch shaft |
45.00 90.00 new |
with busing |
| Reverse idler gear |
20.00 |
22 teeth |
| Reverse idler shaft |
5.00 |
|
| 1st/reverse speed sliding gear |
25.00 |
13 teeth |
| 2nd/3rd speed slide gr. |
25.00 |
need to know if 16/26 teeth or 17/26 |
| Counter shaft & bevel pinion |
20.00 |
10 teeth |
| Reverse speed gear |
25.00 |
35 teeth |
| Speed gear spacers |
1.00 |
let us know which one you need |
| 1st/Rev speed gear |
25.00 |
39 teeth |
| 2nd speed gear |
25.00 |
need to know if 35 or 36 teeth |
| 3rd speed gear |
15.00 |
26 teeth |
| countershaft bearing retainer |
10.00 |
|
| |
|
|
| Gear shift asm |
45.00 |
need to know if straight or bent shifter |
| Shift forks |
25.00 |
1st/Rev OR 2nd/3rd each |
| Shifter rods |
1.00 |
let us know which one |
| Gear shift poppet ball & spring |
.50 cents |
|
| |
|
|
| Final
Drive |
|
|
| Rear axle housing |
85.00 |
through shop cleaned, checked for
cracks. Advise part number with R #
and if for cub or loboy |
| Rear axle |
25.00 |
state if for RT or LT |
| LT rear axle nut |
1.00 |
|
| Rear axle bearing spacer |
1.00 |
|
| Rear axle drive gear |
20.00 |
70 teeth need part # or serial # |
| LT rear axle bear cap |
5.00 |
|
| RT rear axle seal retainer |
5.00 |
|
| RT rear axle nut |
5.00 |
|
| Rear axle housing pan |
15.00 |
|
| Rear axle tube |
30.00 |
(differential shaft housing) |
| Short axle |
35.00 |
(LT differential shaft) 12 teeth |
| Long axle |
25.00 |
(RT differential shaft) 12 teeth |
| |
|
|
| Belt pulley
& PTO |
|
|
| Pto Cover/Guard |
23.00 |
New made like original |
| Pto adaptor cover |
15.00 |
|
| Pto shaft oil seal retainer |
20.00 |
|
| Pto shaft |
65.00 new 30.00 used |
|
| Pto shifter clutch |
15.00 30.00 new |
|
| Pto Collar |
35.00 |
new |
| Pto shifter asm |
20.00 25.00 new |
lever, spring, collar, and shaft |
| Pto shifter guide |
10.00 |
new |
| Pto asm complete |
75.00 |
above less guard and shifter asm with used collar |
| Belt pulley drive asm |
90.00 |
includes 9" flat belt pulley |
| Pto Bearing kit New |
47.00 |
seal, bearings, snap, rings & retaining ring |